Skip to content
Tool Corner

Boiled Egg Timer Simulator: How Long for the Yolk You Want?

A published heat-conduction formula estimates how long a whole egg needs in hot water for the edge of its yolk to reach a chosen temperature, and how egg size, a cold start, a simmer or altitude change that time.

Illustration of a boiled egg cut open on a plate beside a kitchen timer
Illustration
Built and verified by Jogeswara, Founder and Engineer, MSc, PMP — Tool CornerModel stated in full belowReviewed
Doneness
Egg size
UK/EU
Skip to content
Tool Corner

Boiled Egg Timer Simulator: How Long for the Yolk You Want?

A published heat-conduction formula estimates how long a whole egg needs in hot water for the edge of its yolk to reach a chosen temperature, and how egg size, a cold start, a simmer or altitude change that time.

Illustration of a boiled egg cut open on a plate beside a kitchen timer
Illustration
Built and verified by Jogeswara, Founder and Engineer, MSc, PMP — Tool CornerModel stated in full belowReviewed
Last reviewed: Sources: C. D. H. Williams, University of Exeter: The Science of Boiling an Egg; University of Exeter, Theoretical Physics
Doneness
Egg size
{{ g.label }}
Other egg types
Estimates only. This formula is built around chicken eggs; duck and goose shells are thicker, so treat these times as a rough guide and check one egg.
* Extrapolated by this page, rough guide only: the source's formula is only checked against its own worked examples near 63 °C.

Try this: {{ tryTxt }}

Estimated time
{{ bigTime }}

{{ headline }}

Egg timer
{{ tmShow }}

Start when the egg goes into water that is already at temperature.

{{ tmNote }}

{{ tmMsg }}

Times for every size at this doneness

{{ cmpCap }}

SizeMassTime
{{ r.name }}← your egg{{ r.g }} g{{ r.t }}
How this number was worked out
{{ w }}

27.0509 s per g2/3 is computed from the source's density, conductivity and heat capacity; the full formula and legend are under "How it works" below.

Time
{{ cTime }}
Water temperature used
{{ cWater }}
Ratio to the default
{{ cRatio }}
Time at the default egg
{{ cDef }}
Time against yolk edge target
Time against egg mass
Time against altitude
Honesty note

This is an estimate for a whole egg placed in a pan of water. Real eggs vary in shape, shell, air cell and freshness, and pans vary in how much the water cools when the egg goes in. The doneness temperatures are rough guides. This is not food-safety advice: the page cannot tell whether an egg is safe to eat. Anyone who is pregnant, elderly, very young or has a weakened immune system should follow their local food-safety guidance on how well eggs should be cooked.

What your result means

The time is how long the formula estimates the egg must sit in the water, starting the moment it goes in, until the edge of the yolk reaches your target temperature. Start the timer when the egg goes into water that is already at temperature, not when you put a cold pan on the heat. The animation's curve is illustrative only: it is a smooth shape drawn to start at your egg's temperature and arrive at the target exactly at the formula's time, not a solution of the heat equation.

If the target is at or above the water temperature, no time is shown. Water at 80 °C can never bring any part of an egg above 80 °C, so a yolk target of 85 °C is never reached.

What happens inside an egg as it heats

An egg in hot water heats from the outside in. Heat crosses the shell, warms the white next to it, and only slowly works its way to the middle. The outer white sets first while the centre is still cold. The source notes that fresh egg whites set over about 62 to 65 °C and yolks over about 65 to 70 °C, and that setting is a gradual chemical change, not a switch at one temperature.

The formula follows only one number: the temperature at the boundary of the yolk. When that reaches about 63 °C the source calls the egg ready, with a white that is slightly less than firm. Higher targets mean more of the yolk has set. This page lets you choose other targets, but those are extrapolations: the source only checks the formula against its own examples at 63 °C.

Watch: what happens inside the egg

This short cutaway shows an egg cooking from the shell inwards, from runny to jammy to hard-boiled.

Read what the video shows

The video shows a boiled egg cut in half while it cooks in 100 degree Celsius water.

Heat moves in from the outside, so the white next to the shell warms first. The white turns from clear to white; egg white sets at about 62 to 65 degrees Celsius.

Runny yolk: the yolk edge reaches 63 degrees Celsius, the white is set and the yolk is still liquid.

Jammy yolk: the yolk edge reaches 70 degrees Celsius, thick and sticky in the middle.

Hard-boiled yolk: the yolk edge reaches 77 degrees Celsius, firm all the way through.

Illustrative cutaway timed to this simulator's own estimate. Real times vary.

Also on YouTube: watch this cutaway as a Short on the Tool Corner channel.

Why the time grows with mass to the power two thirds

Heat spreading through a solid takes a time that grows with the square of the distance it must travel. For a sphere of fixed density, the radius grows with the cube root of the mass, so the radius squared grows with mass to the power two thirds. Double the mass and the time rises by 22/3, about 1.59 times, not twice.

With a fridge-cold start and a 65 °C target, a 45 g egg takes 4 min 11 s and a 70 g egg 5 min 38 s, against 4 min 54 s for the default 57 g egg.

Why cold eggs take longer

An egg straight from the fridge has further to climb. The logarithm in the formula compares the starting gap between water and egg with the gap still left at the end. A 57 g egg at 4 °C needs 4 min 54 s to reach 65 °C at the yolk edge; the same egg at 20 °C needs 3 min 41 s. The difference is a little over a minute, which is why recipes that ignore where the egg was stored often disagree.

Why altitude and simmering add time

Water boils at a lower temperature where the air pressure is lower. This page uses an approximation of about 1 °C lower for every 300 m, so water boils at about 96.7 °C at 1,000 m and 93.3 °C at 2,000 m. The source's own altitude graph uses standard-atmosphere data instead; the approximation is this page's. Cooler water pushes less heat into the egg, and the time grows most when the target is close to the water temperature: the default egg needs 4 min 54 s at sea level, 5 min 20 s at 1,000 m and 5 min 50 s at 2,000 m.

A simmer does the same thing at any altitude. Use the water slider to hold the water below boiling: at 95 °C the default egg needs 5 min 35 s. The source also reports an observer on a 1,917 m mountain who found eggs took noticeably longer than the formula predicts, and suggests a single setting temperature is too simple for slow, cooler cooking. Treat high-altitude times as a lower bound.

How it works: the formula

t = M2/3 × c ρ1/3 / (K π2 (4π/3)2/3) × ln[ 0.76 × (Te − Tw) / (Ty − Tw) ]
c ρ1/3 / (K π2 (4π/3)2/3) = 27.0509 s per g2/3 = 0.45085 min per g2/3 ≈ 0.451
Tw = min(water setting, 100 − h / 300)
  • t the time in the water. M the egg's mass in grams.
  • Te the egg's starting temperature, Tw the water temperature and Ty the target temperature at the edge of the yolk, all in °C. The ratio inside the logarithm is the same as 0.76 × (Tw − Te) / (Tw − Ty).
  • ρ = 1.038 g cm−3, K = 5.4 × 10−3 W cm−1 K−1 and c = 3.7 J g−1 K−1: the density, thermal conductivity and specific heat capacity of "egg", as printed by the source. The page computes the prefactor from these three numbers; it is not typed in.
  • The egg is treated as a uniform sphere placed straight into water held at Tw. The factor 0.76 comes from the source's solution of the heat-diffusion equation for a sphere.
  • h the altitude in metres. The boiling-point rule is this page's approximation, not the source's. If you set the water lower than the boiling point, the lower value is used.
  • If Ty is at or above Tw, or the egg starts hotter than the water, the formula has no answer and no time is shown.

Worked example: checked against the source

The source gives four worked examples, all in boiling water with the yolk edge at 63 °C. This page's formula reproduces them to within the source's rounding to half minutes; the room-temperature case is the furthest off, by about 16 seconds.

EggSource saysThis page
57 g, from the fridge (4 °C)4.5 min4.53 min (4 min 32 s)
57 g, room temperature (21 °C)3.5 min3.23 min (3 min 14 s)
47 g, from the fridge4 min3.99 min (3 min 59 s)
67 g, from the fridge5 min5.05 min (5 min 3 s)

The default on this page goes one step further, to a 65 °C yolk edge: a 57 g egg from the fridge in boiling water at sea level needs 4 min 54 s (4.91 min). That target is beyond what the source checks.

How to use this simulator

  • Pick a doneness and an egg size, or weigh the egg and use the mass slider, then pick where it was stored. Move the sliders, or tab to one and use the arrow keys.
  • Choose a yolk edge target. 63 °C is the source's "ready" value; the starred presets are this page's rough extrapolations.
  • Set your altitude, and lower the water slider if you cook at a simmer rather than a full boil.
  • Run again replays the animation. The egg timer counts down from the estimate. Copy link saves every setting. Save picture downloads the egg picture with the settings and time printed underneath.

Size, start, altitude and water in numbers

All times come from the page's own formula, t = k × M2/3 × ln(0.76 × (Tw − Te) ÷ (Tw − Ty)), with the constant k = 27.05 s per g2/3 derived from the egg's density, conductivity and heat capacity. The page's own caution applies: only the 63 °C figures are close to what the source checks, and 70 and 77 °C, marked with an asterisk, are extrapolations.

Time by egg size from the fridge (4 °C start, boiling water)
EggMassRunny, 63 °CJammy, 70 °C*Hard, 77 °C*
UK/EU Small48 g4 min 3 s5 min 18 s6 min 52 s
US Large57 g4 min 32 s5 min 56 s7 min 43 s
UK/EU Medium58 g4 min 35 s6 min 0 s7 min 48 s
US XL64 g4 min 54 s6 min 25 s8 min 20 s
UK/EU Large68 g5 min 6 s6 min 41 s8 min 40 s
US Jumbo71 g5 min 15 s6 min 52 s8 min 55 s
UK/EU Very large (XL)78 g5 min 35 s7 min 19 s9 min 30 s

A 58 g UK/EU medium egg from the fridge takes 4 min 35 s for a runny yolk. A large one at 68 g takes 5 min 6 s, about 31 seconds more. Egg size matters, but less than people expect.

Where the egg starts

Time by starting temperature (57 g egg, boiling water)
Egg starts at63 °C65 °C70 °C*77 °C*
4 °C4 min 32 s4 min 54 s5 min 56 s7 min 43 s
10 °C4 min 6 s4 min 28 s5 min 30 s7 min 17 s
20 °C3 min 19 s3 min 41 s4 min 43 s6 min 29 s

Taking the egg out of the fridge first saves 1 min 13 s at 63 °C, 27% of the cooking time, which is more than the 1 min 3 s between a UK/EU Small and a Large egg.

Altitude and simmering

Time by altitude (57 g egg from the fridge, water at the local boiling point)
AltitudeWater boils at63 °C65 °C77 °C*Extra time at 65 °C
0 m100.0 °C4 min 32 s4 min 54 s7 min 43 s–
500 m98.3 °C4 min 43 s5 min 7 s8 min 6 s+4%
1,000 m96.7 °C4 min 56 s5 min 20 s8 min 31 s+9%
1,500 m95.0 °C5 min 9 s5 min 35 s8 min 59 s+14%
2,000 m93.3 °C5 min 23 s5 min 50 s9 min 31 s+19%
3,000 m90.0 °C5 min 54 s6 min 25 s10 min 47 s+31%

The page lowers the boiling point by 1 °C per 300 m, so at 2,000 m the water is at 93.3 °C and a 65 °C yolk takes 19% longer. A hard yolk is hit harder, because the target is closer to the water temperature.

Time by water temperature (57 g egg from the fridge, sea level)
Water63 °C65 °C77 °C*
100 °C4 min 32 s4 min 54 s7 min 43 s
95 °C5 min 9 s5 min 35 s8 min 59 s
90 °C5 min 54 s6 min 25 s10 min 47 s
85 °C6 min 52 s7 min 30 s13 min 38 s
80 °C8 min 10 s9 min 0 s19 min 45 s
77 °C9 min 12 s10 min 13 snever reached
70 °C13 min 9 s15 min 24 snever reached

Simmering costs more than most people allow. Water at 90 °C adds 30% at 63 °C and 40% at 77 °C. At 77 °C or below, a 77 °C yolk is never reached at all, because the water is no hotter than the target.

Mass to the power two thirds

Why mass counts less than you would think (4 °C start, 65 °C yolk edge, boiling water)
Egg massTimeMass against the 57 g eggTime against the 57 g egg
30 g3 min 12 s0.53 ×0.65 ×
45 g4 min 11 s0.79 ×0.85 ×
57 g4 min 54 s1.00 ×1.00 ×
70 g5 min 38 s1.23 ×1.15 ×
100 g7 min 8 s1.75 ×1.45 ×
114 g7 min 47 s2.00 ×1.59 ×

Heat has to travel a distance that grows with the cube root of the mass, and the time grows with that distance squared, which is mass to the power two thirds. Doubling the mass takes 1.59 times as long, not twice.

Six mistakes when timing an egg

  • Timing from the moment the pan goes on the heat. The formula starts when the egg goes into water that is already at temperature. Time spent heating the water is extra and varies with the pan and the hob.
  • Ignoring where the egg was stored. A fridge egg needs 1 min 13 s more than a 20 °C egg for a runny yolk, which is why recipes that do not say where the egg starts disagree.
  • Doubling the time for double the egg. Time goes with mass to the power 2/3: a 114 g egg takes 1.59 times as long as a 57 g one, not twice.
  • Treating a simmer as a boil. The yolk edge approaches the water temperature, so cooler water costs time quickly: 85 °C water takes 52% longer than boiling for a runny yolk, and a 77 °C yolk in 77 °C water never arrives.
  • Forgetting altitude. At 2,000 m the water boils at about 93.3 °C and the same egg takes 19% longer to reach 65 °C.
  • Trusting the jammy and hard times as much as the runny one. The page marks 70 and 77 °C as extrapolations, and the shell, egg shape and pan all shift real times. It is a guide, not food-safety advice: follow local guidance for anyone vulnerable.

Embed this calculator on your site

You can put this tool on your own page, blog or lesson site for free. Copy the code below and paste it into your page. Please keep the credit line under the tool. The embedded version shows no ads, loads no analytics and sets no cookies.

<iframe src="https://toolcorner.net/embed/boiled-egg-simulator" title="Boiled Egg Timer" width="100%" height="1840" style="border:0;max-width:760px" loading="lazy"></iframe>
<p style="font-size:13px">Calculator by <a href="https://toolcorner.net/labs/boiled-egg-simulator">Tool Corner</a></p>

Cite this page

If you use this tool in a report, assignment or article, you can cite it like this.

Tool Corner. (2026). Boiled Egg Timer [Online calculator]. https://toolcorner.net/labs/boiled-egg-simulator

Boiled Egg Timer. Tool Corner. https://toolcorner.net/labs/boiled-egg-simulator. Retrieved [date].

Assumptions & limitations: what the model leaves out

  • A real egg is not a uniform sphere. The source points out that shell, white and yolk have different thermal properties and the egg is closer to nested ellipsoids.
  • The heat absorbed when the white sets, and the change in its properties as it does, are ignored.
  • The water is assumed to stay at the set temperature. A cold egg in a small pan cools the water, which adds time.
  • Setting happens over a range of temperatures and depends on time as well, so one target temperature is a simplification, most of all at altitude.
  • Freshness, the air cell and cracking are not modelled. Nothing here judges food safety.

Frequently asked questions

How long for a soft boiled egg?

For a runny yolk, aim for 63 °C at the yolk edge, which the source calls ready. From the fridge (4 °C) into boiling water at sea level, the formula gives about 4 min 35 s for a medium egg (58 g) and 5 min 6 s for a large egg (68 g). A medium egg at room temperature (20 °C) needs about 3 min 21 s.

How long for a hard boiled egg?

Using a 77 °C yolk edge, from the fridge into boiling water at sea level, the formula gives about 7 min 48 s for a medium egg (58 g) and 8 min 40 s for a large egg (68 g). 77 °C is this page's extrapolation beyond what the source checks, so treat these times as a rough guide.

Does egg size change the time?

Yes, but less than you might expect, because the time grows with the mass to the power two thirds. For a 65 °C yolk edge, from the fridge into boiling water at sea level, a small egg (48 g) needs about 4 min 22 s and a very large egg (78 g) about 6 min 3 s.

How long does a medium egg take for a soft yolk?

With the formula used here, a 57 g egg from the fridge at 4 °C, put straight into boiling water at sea level, takes about 4 minutes 32 seconds for the edge of the yolk to reach 63 °C, which the source calls ready. The source rounds this to four and a half minutes.

Why does a fridge-cold egg need longer?

It starts further from the target, so more heat has to reach the centre. For a 57 g egg and a 65 °C yolk edge, the time is about 4 minutes 54 seconds from 4 °C and 3 minutes 41 seconds from 20 °C.

Can I use this for duck or quail eggs?

Only as a rough guide. The formula is built around chicken eggs. For a 63 °C yolk edge, from the fridge into boiling water at sea level, it gives about 1 min 25 s for a quail egg (about 10 g) and 5 min 27 s for a duck egg (about 75 g). Duck shells are thicker, so check one egg before cooking a batch.

Why do eggs take longer at altitude?

Water boils at a lower temperature higher up. Using an approximation of 1 °C per 300 m, the default egg goes from about 4.9 minutes at sea level to 5.8 minutes at 2,000 m. The source reports real high-altitude eggs taking longer still.

Can this tell me whether an egg is safe to eat?

No. It estimates a temperature, not safety. Anyone who is pregnant, elderly, very young or has a weakened immune system should follow their local food-safety guidance on how well eggs should be cooked.

Related calculators

Sources and references

Last updated
Was this result right?
What next?
Educational only

This simulator illustrates a simplified heat-conduction estimate. It is not food-safety advice and cannot tell whether an egg is safe to eat.

Cooking something else? Air fryer and oven simulator and guide