Skip to content
Tool Corner

Meteor Entry Simulator: Will It Burn Up?

Send a rock into Earth's atmosphere and follow it down: does it burn up, break apart high in the sky, or reach the ground, and how fast is it going on the way?

Illustration of a flaming meteor streaking towards a blue planet
Illustration
Built and verified by Jogeswara, Founder and Engineer, MSc, PMP — Tool CornerModel stated in full belowReviewed
Skip to content
Tool Corner

Meteor Entry Simulator: Will It Burn Up?

Send a rock into Earth's atmosphere and follow it down: does it burn up, break apart high in the sky, or reach the ground, and how fast is it going on the way?

Illustration of a flaming meteor streaking towards a blue planet
Illustration
Built and verified by Jogeswara, Founder and Engineer, MSc, PMP — Tool CornerModel stated in full belowReviewed
Outcome

{{ outcome }}

{{ srTxt }}

Entry mass
{{ m0Txt }}
Entry kinetic energy
{{ E0Txt }}
{{ evLab }}
{{ evTxt }}
Speed then
{{ vTxtThen }}
Mass left
{{ leftTxt }}
Energy still carried
{{ eEndTxt }}
Peak deceleration
{{ peakTxt }}
Ground impact speed
{{ impactTxt }}
Ablation efficiency Λ used
{{ lamTxt }}

On the way down

Speed against height
Deceleration (g) against height
Dynamic pressure against height
Mass remaining against height
Honesty note

This is a single-body model: one sphere that keeps its shape, does not spin and is not followed after it first breaks. It uses round constants, no wind and a simple atmosphere. It is for learning how entry works. It is not a hazard-assessment tool and cannot forecast what a real object would do.

Why meteors glow

A rock arriving from space hits the top of the atmosphere fast: this simulator covers 11.2 to 72 km/s, many times faster than a rifle bullet. It cannot push the air out of the way gently. Instead it rams into it, squeezing the air in front into a thin, extremely hot cap. That compressed, superheated air glows, and so does the melting surface of the rock. The streak of light we call a meteor is mostly this glowing air and vapour, seen from far below.

The light starts high in the atmosphere, where the air is thin but the speed is so great that even a thin gas carries a huge amount of energy past the rock every second.

Drag and ablation in plain words

Two things happen to the rock as it falls. Drag slows it down: the force is the air density times the speed squared times the size of its front face, and it gets much stronger as the rock reaches thicker air. Ablation eats it away: some of the energy of that hot air is carried into the rock's surface, which melts and boils off, so the rock loses mass as it goes.

Both effects depend on the ratio of surface to mass. A small rock has a lot of surface for very little mass, so drag slows it in seconds and ablation can strip it away entirely. A large rock has much more mass behind each square metre of its face, so the same air barely slows it. That is why grains and pebbles burn up while a large, dense body can cross the whole atmosphere at nearly its entry speed.

What dynamic pressure is, and why rocks break

The air piling up in front of the rock pushes on it with a pressure roughly equal to the air density times the speed squared. This is the dynamic pressure, and it is what you would feel on your hand out of a car window, scaled up beyond imagination. In this model, at 19 km/s and 50 km up it is already about 0.85 MPa: more than eight times the pressure of the whole atmosphere at sea level, pressing on the front face.

Every rock has a strength, the pressure it can take before it cracks. The presets here run from 1 MPa for a weak stony body to 50 MPa for iron; they are illustrative values, not measurements of any real object. As the rock dives into thicker air, the dynamic pressure climbs. If it climbs past the strength, the rock fractures. In reality the pieces then spread out, present far more surface to the air, and dump their energy very quickly: an airburst. This model stops at the moment of first fracture and reports where that happens and how much energy the rock is still carrying. Because breakup is set by the moment ρv² reaches the strength, its height barely depends on size: with the other settings at their defaults, rocks from 5 m to 40 m all break up between 48.71 and 48.76 km.

Why shallow angles and slow speeds matter

The angle sets how long the rock spends in the thin upper air. On a shallow path it crosses a long stretch of high, thin air, so a small rock slows and burns away higher up and a larger one reaches the ground much more slowly. Where a rock simply breaks when the air pressure on it reaches its strength, though, the height of first breakup barely depends on the angle in this model: the pressure is set by air density and speed, and the speed has hardly changed by then.

Speed works through the square in the dynamic pressure. A faster rock reaches its breaking pressure in thinner air, so it breaks up higher. A slower rock has to get deeper into the atmosphere before the pressure is high enough, which is why slow, strong bodies are the ones most likely to reach the ground in one piece.

How the model works

The rock is a sphere of fixed density. Its radius follows from its mass, so as it loses mass it shrinks but stays round. The simulation starts it at 120 km and steps forward through time with the fourth-order Runge–Kutta method, tracking speed, flight-path angle, height and mass:

dv/dt = −Cd ρ A v² / (2m) + g sin γ
dγ/dt = (g/v − v/(R+h)) cos γ
dh/dt = −v sin γ
dm/dt = −Λ ρ A v³ / (2Q)
  • v speed, γ flight-path angle below the horizontal (90° is straight down), h height, m mass, A the cross-section of the sphere.
  • Air density ρ = 1.225 × e−h/8000 kg/m³. The 8 km scale height is a round value; the real atmosphere's scale height changes with height.
  • Gravity g = 9.80665 × (R/(R+h))², with Earth's radius R = 6,371 km. The (g/v − v/(R+h)) term lets a shallow path curve with the Earth.
  • Drag coefficient Cd = 1.0.
  • Ablation efficiency (heat-transfer coefficient) Λ: by default it depends on size, 1.0 for bodies up to 10 cm, 0.1 for 10 m and larger, and a straight line on a log scale in between (a 5 m body gets 0.141). This schedule is an assumption made for this page: large bodies shield themselves with their own vapour, so less of the heat reaches them, while small ones do not. The real value depends on the flow regime and is not measured here. The results for small meteoroids are the ones most sensitive to it; you can set your own value from 0.05 to 1.0.
  • Heat of ablation Q: 8 MJ/kg for stony and iron, 2.5 MJ/kg for icy bodies. These are round illustrative values, assumed for this page, not measurements.
  • The rock breaks up the first time ρv² reaches the strength. It burns up when less than 0.1% of its entry mass is left. With "No breakup" chosen, it is never allowed to fracture.
  • Step rule: each step moves the rock at most 25 m in height and changes its speed or mass by at most 0.1%, and is never longer than 0.05 s. The breakup and burn-up points are found by interpolating within the step. Halving every step changes the reported numbers by less than 0.1%.
  • Kinetic energy is reported in kilotonnes of TNT, where 1 kt = 4.184 × 10¹² J.

A real-world comparison

NASA describes the 2013 fireball over Chelyabinsk, Russia, as a house-sized object entering at over 18 km/s, blowing apart about 23 km above the ground and releasing energy equivalent to around 440,000 tons of TNT. The defaults here, a 19 m stony rock at 19 km/s, carry a similar 511 kt at entry. In this model, with a strength of 1 MPa, the rock first fractures much higher, near 49 km. That is not a contradiction: the model stops at the very first crack, while the real object went on breaking up and released most of its energy lower down, which this page does not model.

Strength, size, angle and speed in numbers

Each row was run through the simulator's own model: a single sphere with drag, gravity, the curve of the Earth and ablation, started at 120 km. Breakup is the first moment the dynamic pressure ρv² reaches the body's strength. The numbers are illustrations of that model, not forecasts for any real object.

Where a 19 m rock first breaks up at 19 km/s and 18° (stony density 3,300 kg/m³ except the last row, which is a solid iron body)
StrengthHeight of first breakupSpeed thenMass leftEnergy still carriedPeak deceleration
Weak stony, 1 MPa48.7 km19.02 km/s99.6%510 kt1.2 g
Strong stony, 10 MPa30.2 km18.86 km/s95.7%482 kt12.4 g
Iron strength, 50 MPa16.6 km18.00 km/s78.3%359 kt66.1 g
Iron strength and density (7,800 kg/m³), 50 MPa17.1 km18.64 km/s90.7%1,055 kt26.6 g

The weak 1 MPa rock breaks near 48.7 km. A 10 MPa rock holds together to 30.2 km and a 50 MPa one to 16.6 km, by which time it has lost about 22% of its mass and 30% of its energy. The rock is still carrying most of its energy at breakup, and what happens next, the airburst, is not modelled.

Size and burning

Size against outcome with "No breakup" selected (stony, 19 km/s, 18°)
DiameterEntry energyOutcomeWhereSpeed thereMass left
0.01 m0.31 MJBurns up74.6 km15.85 km/sunder 0.1%
0.10 m312 MJBurns up56.5 km15.86 km/sunder 0.1%
1 m0.07 ktBurns up24.5 km3.65 km/sunder 0.1%
5 m9.32 ktReaches the groundground0.45 km/s4.0%
19 m511 ktReaches the groundground10.41 km/s20.3%
50 m9,318 ktReaches the groundground15.73 km/s48.4%

Small rocks burn up, large ones do not. A 1 m rock with ablation on is gone by about 24.5 km, but a 5 m rock reaches the ground slowly, after losing 96% of its mass. A 19 m rock arrives at 10.4 km/s with a fifth of its mass left, and a 50 m body arrives at 15.7 km/s with nearly half. The big rock is protected by having more mass behind each square metre of its face.

For first breakup the angle moves the time, not the height

Entry angle with the 1 MPa default (19 m rock at 19 km/s)
Angle below horizontalHeight of first breakupTime from 120 km to breakupMass left at breakup
90°48.76 km3.7 s99.9%
45°48.76 km5.3 s99.8%
30°48.76 km7.6 s99.8%
18°48.75 km12.7 s99.6%
10°48.73 km26.4 s99.0%

The height at which the rock first breaks hardly depends on the angle: it changes by about 30 m between a vertical entry and 10°, because the breakup point is set by the air density and speed, and not by the route. What the angle changes is how long the descent takes, 3.7 seconds from vertical and 26 seconds at 10°, and so how far along its track the rock travels on the way.

Entry angle for smaller rocks with "No breakup" selected (stony, 19 km/s)
Angle below horizontal1 m rock burns up at5 m rock reaches the ground at5 m rock mass left
90°14.1 km9.33 km/s8.7%
45°17.0 km5.78 km/s5.4%
18°24.5 km0.45 km/s4.0%
10°32.4 km0.28 km/s4.0%

The angle matters a great deal for rocks that do not break. A 1 m rock burns up at 14.1 km if it comes in vertically but at 32.4 km at 10°, because the shallow path meets much more air on the way down to any given height. A 5 m rock arrives at 9.33 km/s from vertical but at only 0.28 km/s at 10°. The two tables fit together: breakup height is set by pressure, and burn-up and arrival speed are set by how much air the path crosses.

Speed raises the breakup height

Entry speed with the 1 MPa default (19 m rock at 18°)
Entry speedHeight of first breakupEnergy at entryEnergy still carried at breakup
11.2 km/s40.3 km178 kt178 kt
15.0 km/s45.0 km319 kt318 kt
19.0 km/s48.7 km511 kt510 kt
30.0 km/s56.0 km1,275 kt1,270 kt
50.0 km/s64.2 km3,541 kt3,527 kt
72.0 km/s70.1 km7,342 kt7,312 kt

A faster rock reaches the same pressure in thinner air. At 11.2 km/s breakup is at 40.3 km. At 72 km/s it is at 70.1 km, but the energy involved has grown more than forty-fold, from 178 kt to 7,342 kt.

Six mistakes when reading a meteor entry

  • Using it as a hazard forecast. The page says so itself. One sphere, one fixed drag coefficient and round material constants cannot predict what a real object will do.
  • Expecting small rocks to survive. Ablation strips mass in proportion to surface area. A 1 cm pebble at 19 km/s is gone by about 75 km, roughly eight seconds after entering, and the table shows the same for sizes up to 1 m.
  • Reading breakup as the ground impact. Breakup is where the first fracture begins. The page stops there, with the rock still carrying hundreds of kilotonnes of energy for the defaults, and does not model what the fragments do next.
  • Thinking a steeper angle breaks the rock lower. In this model the angle barely moves the height of first breakup, as the third table shows. Speed and strength set it. The angle does matter for whether a small rock burns up and how fast a larger one arrives, as the next table shows.
  • Comparing kilotonnes of TNT with damage. That figure is energy at entry. How much reaches the surface, and in what form, depends on height, shape and fragmentation that the model does not follow.
  • Treating the strength presets as measurements. 1, 10 and 50 MPa are illustrative round values. Real asteroids have cracks and weak zones, and their strength varies enormously.

Embed this calculator on your site

You can put this tool on your own page, blog or lesson site for free. Copy the code below and paste it into your page. Please keep the credit line under the tool. The embedded version shows no ads, loads no analytics and sets no cookies.

<iframe src="https://toolcorner.net/embed/meteor-entry-simulator" title="Meteor Entry Simulator" width="100%" height="1440" style="border:0;max-width:760px" loading="lazy"></iframe>
<p style="font-size:13px">Calculator by <a href="https://toolcorner.net/labs/meteor-entry-simulator">Tool Corner</a></p>

Cite this page

If you use this tool in a report, assignment or article, you can cite it like this.

Tool Corner. (2026). Meteor Entry Simulator [Online calculator]. https://toolcorner.net/labs/meteor-entry-simulator

Meteor Entry Simulator. Tool Corner. https://toolcorner.net/labs/meteor-entry-simulator. Retrieved [date].

Assumptions & limitations: what the model leaves out

  • Grazing paths: at very shallow angles (7 degrees and below for the default rock) the rock can pass through the upper air and leave again. The page then reports a skip at 120 km and does not follow the rock afterwards.
  • Nothing after the first fracture: the fragments, the flattening and spreading of a crushed body, and the airburst shock wave are not modelled. The page only tells you where breakup starts and how much energy is still there.
  • One sphere of fixed density, with no spin, no change of shape and no tumbling.
  • A simple exponential atmosphere with no weather, wind or day-to-day changes.
  • A fixed drag coefficient, an assumed size schedule for the ablation efficiency, and round heat-of-ablation values. Real values change with speed, height, size and material.
  • Strength is a single number. Real asteroids have cracks and weak zones, and their effective strength can change as they break.

Because of these, treat every number on this page as an illustration of how the physics behaves, not as a prediction.

How to use this simulator

  • Choose a diameter with the slider, from 1 cm to 200 m; it is logarithmic, so each part of its travel covers a factor of ten.
  • Pick a material, or type your own density. Choose a strength preset or type a strength in megapascals; "No breakup" lets the body fall without fracturing.
  • Set the entry speed and angle, and switch ablation off to see how much of the slowing comes from drag alone.
  • Press Run again to replay the descent. Copy link saves every setting in the address, and Save picture downloads the side view with the settings and outcome printed underneath.

Frequently asked questions

Why do most meteors burn up?

Most of them are tiny. A grain or pebble has a lot of surface for its mass, so the air slows it within seconds and the heat strips its surface away high in the atmosphere. NASA describes most meteor-shower debris as between a grain of sand and a pea, and says it burns up before reaching the ground. In this model a 1 cm stony grain entering at 20 km/s and 45 degrees burns up at about 68.6 km, and a 10 cm pebble at about 50.2 km.

Why does a rock break up instead of just burning?

The air in front of it pushes back with a pressure equal to the air density times the speed squared. That pressure grows enormously as the rock dives into thicker air at many kilometres per second. When it is greater than the rock can withstand, the rock fractures. With the defaults here, a 19 m stony rock with a strength of 1 MPa reaches that point at about 48.7 km up, still carrying almost all of its 511 kt of energy.

Why do iron meteoroids get further?

Iron is more than twice as dense as stone and much stronger. A dense body carries more mass behind each square metre of its front, so drag slows it less, and a high strength means the air pressure needed to break it is only reached low down or not at all. In this model a 100 m iron body at 20 km/s and 45 degrees reaches the ground at about 19.8 km/s.

Does a shallow angle make a difference?

Yes. A shallow path spends much longer in thin upper air, so a small body has more time to slow down and ablate before it reaches thick air. A steep path dives quickly into dense air at nearly full speed, which raises the air pressure on it sooner.

Can this tell me what a real incoming object would do?

No. It is a teaching model with round numbers and a single body of fixed shape that stops at the first fracture. Real assessments of incoming objects are made by professional teams with far more detailed models. Use this to understand the physics, not to forecast anything.

Related calculators

Sources and references

Last updated
Was this result right?
What next?
Educational only, not a hazard assessment

This simulator illustrates the physics of atmospheric entry with a simplified model. It does not assess, predict or forecast the risk from any real object.